Women's mountain walking shoes - MH100 - Grey/Pink

WOMEN'S

HIKING

2 Years

We have classified our product in terms of performance and function to suit the 3 levels of Mountain Walking: - Occasional: a dozen hikes a year for approximately 3 to 4 hours, under 10 km and under 700m of vertical distance. - Regular: twenty outings a year. 4 to 6 hours, 10 to 20 km, 700 to 1200m of vertical distance per outing. - Intensive: for over 20 outings per year. For over 6 hours, over 20 km, 1200 to 2000m of vertical distance per outing.

For the inner sole fabric coating of these shoes, we dye the thread during manufacturing to reduce the environmental impact. Textile dyeing requires a lot of water but also produces waste water from the dye baths. To reduce this environmental impact, we use a mass pigmentation process that involves adding the colour pigments when the yarn itself is produced.

The grip of our soles is certified. To be awarded certification, the boots must pass laboratory tests to assess the grip rate on different surfaces (Smooth, Rugged, Dry, Wet). To validate these tests, we assess the quality of our soles in the field, in the mountains, by a panel of representative testers over 500 km

The most important thing is to try on several sizes and styles of boots to find the one most suited to you! You can take a size above your usual one to prevent the toes from bumping into the toe box when going downhill, provided the foot is properly supported to avoid friction. Tip: keep your toenails short and, before a long descent, check that your lacing is tight enough to prevent your foot from sliding forwards inside the boot.

Some Decathlon stores have a test route. 1. Try on both shoes, standing up, with the socks worn for hiking. 2. Tighten the laces, taking care to correctly balance the tightening. 3. Check two points: - the heel does not come up before the boot when you walk uphill. - the foot does not slide and the toes do not press against the front when going downhill. 4. Try on several sizes and models. Break them in gradually to adapt them to your foot.

All our shoes are tested for initial comfort and comfort in use by hikers (who do not work for Decathlon) under the same conditions you will encounter yourself when hiking. The aim is to further develop the product and validate it as objectively as possible, for your greatest satisfaction.

Further laboratory tests were conducted to test the following elements: attachment of eyelets and webbing, assembly, toxicology, UV resistance, sole and upper component abrasion, accelerated ageing.

The original insole in your boots is designed to accommodate most feet. A change of insole can bring: 1. Improved support: some soles are preformed or reinforced to better support the arch of the foot. 2. More comfort: the insoles can also provide heat and/or cushioning. 3. Longer life: restore the support and comfort of your shoes by replacing the insole each season.

- Leave to air-dry. - Remove dry mud with a stiff brush. - For stains, clean with a brush and a little warm water - Leave to dry - Spray with a re-waterproofing agent to restore the water-repellent properties of the upper.

Store in a well ventilated dark, dry place.

All our boots are tested for initial comfort and comfort in use by hikers from outside Decathlon under the same conditions you find in use. The aim is to test, develop and confirm the product in the most objective way possible, so you can get maximum enjoyment out of hiking!

Outer sole of : 70.0% Rubber - Styrene Butadiene Rubber, Outer sole of : 30.0% Ethylene Vinyl Acetate Upper of : 60.0% Polyester, Upper of : 20.0% Polyurethane, Upper of : 20.0% Leather - Bovine - Split Lining and sock of : 90.0% Polyester, Lining and sock of : 10.0% Polyamide

We have classified our product in terms of performance and function to suit the 3 levels of Mountain Walking: - Occasional: a dozen hikes a year for approximately 3 to 4 hours, under 10 km and under 700m of vertical distance. - Regular: twenty outings a year. 4 to 6 hours, 10 to 20 km, 700 to 1200m of vertical distance per outing. - Intensive: for over 20 outings per year. For over 6 hours, over 20 km, 1200 to 2000m of vertical distance per outing.

For the inner sole fabric coating of these shoes, we dye the thread during manufacturing to reduce the environmental impact. Textile dyeing requires a lot of water but also produces waste water from the dye baths. To reduce this environmental impact, we use a mass pigmentation process that involves adding the colour pigments when the yarn itself is produced.

The grip of our soles is certified. To be awarded certification, the boots must pass laboratory tests to assess the grip rate on different surfaces (Smooth, Rugged, Dry, Wet). To validate these tests, we assess the quality of our soles in the field, in the mountains, by a panel of representative testers over 500 km

The most important thing is to try on several sizes and styles of boots to find the one most suited to you! You can take a size above your usual one to prevent the toes from bumping into the toe box when going downhill, provided the foot is properly supported to avoid friction. Tip: keep your toenails short and, before a long descent, check that your lacing is tight enough to prevent your foot from sliding forwards inside the boot.

Some Decathlon stores have a test route. 1. Try on both shoes, standing up, with the socks worn for hiking. 2. Tighten the laces, taking care to correctly balance the tightening. 3. Check two points: - the heel does not come up before the boot when you walk uphill. - the foot does not slide and the toes do not press against the front when going downhill. 4. Try on several sizes and models. Break them in gradually to adapt them to your foot.

All our shoes are tested for initial comfort and comfort in use by hikers (who do not work for Decathlon) under the same conditions you will encounter yourself when hiking. The aim is to further develop the product and validate it as objectively as possible, for your greatest satisfaction.

Further laboratory tests were conducted to test the following elements: attachment of eyelets and webbing, assembly, toxicology, UV resistance, sole and upper component abrasion, accelerated ageing.

The original insole in your boots is designed to accommodate most feet. A change of insole can bring: 1. Improved support: some soles are preformed or reinforced to better support the arch of the foot. 2. More comfort: the insoles can also provide heat and/or cushioning. 3. Longer life: restore the support and comfort of your shoes by replacing the insole each season.

- Leave to air-dry. - Remove dry mud with a stiff brush. - For stains, clean with a brush and a little warm water - Leave to dry - Spray with a re-waterproofing agent to restore the water-repellent properties of the upper.